Designing hardware to protect the Internet

September 19, 2016 OpenSystems Media

Increased data capacity has amplified the cost of line cards by tens of thousands of dollars, making quality latching and fastening hardware paramount in the server design process. Integrating captive screws and inject/eject solutions designed with quality materials and proven engineering from the beginning can mean the difference between redundancy and downtime.

Open source models and globalization have changed the way that technology companies approach data center designs, from servers to networking and storage. But while open source designs cost less than traditional enterprise servers, they present new challenges for the designers tasked with integrating these solutions. This may lead to the selection of inferior physical fastening hardware, due to lower upfront cost. Cheaper products are widely available through contract manufactures with unknown suppliers, and may not meet the quality standards required to perform in critical environments, which can result in additional service costs, lost engineering time to redesign systems, and down time.

Considerations for inject/eject hardware

With any inject/eject mechanism (Figure 2), there is the risk of damaging connectors, breaking latches, or making faulty switch engagements when inserting line cards to the chassis – all due to increased forces needed to seat the connectors. For instance, if the connectors are not seated correctly during insertion, the module may lead to data disruption or an intermittent signal.

[Figure 1 | Ergonomic and robust handles secure blades and line cards to ensure proper interface with the microswitch.]

Hot swappable systems are crucial in managing the safety of stored data, because if one system is down and running without a backup, the data is at risk until maintenance can restore redundancy. Integrating a hot swap switch directly into the ejector is an efficient means to assure the hot swap timing is correct. When the ejector lever is released and the integral microswitch sends signal, it releases stored data to a redundant line card, so the faulty card can be serviced or swapped out.

Material selection is another key factor in the design of mechanical lever ejectors (Figure 2). Inferior metals affect aesthetics, where inferior finishes or corrosion can impact the intended finish of the part by the industrial design team. If a non-qualified finish supplier is used to save on budget, it can cause quality issues after multimillion-dollar units have shipped, leading to disruptions and lost revenue.

[Figure 2 | Enterprise hardware products should be engineered with quality materials and minimized design footprint to accommodate multiple faceplate thicknesses and microswitch styles.]

Risk is also present when inserting a line card to the backplane. Ejector systems provide the correct amount of “wipe” by ensuring that board connectors interface properly with the backplane of the shelf. For instance, there is a minimum amount of travel required to maintain the signal integrity through the mating connector. If that travel is not achieved, there is an intermittent signal, or through vibration that signal could be lost. Tolerance stack ups within the system may also affect wipe. These design parameters must be taken into consideration early on in the design process. Working with a supplier that can run mold flow analysis, design for manufacturing (DFM), and dynamic finite element analysis (DFEA) simulations saves time and potential quality issues once products are released.

Considerations for captive hardware

Material selection is equally important when specifying captive hardware, which secures different components, or PC boards and motherboards, securely in place. With captive screws, there is a wide range of materials to choose from, but using the most economic option upfront can lead to operation issues down the line.

Finishes may not withstand fluctuations in temperature (Figure 3) and colors may fade over time. Using high-grade similar materials can also lead to galling. In many cases, the metal flakes generated by stripping the thread fall onto the PC board and cause components to short, once again leading to lost data or data disruption. Stripped hardware also prevents technicians from accessing the server card, further contributing to added costs.

[Figure 3 | Southco’s SMT 4C Captive Screws feature heat-resistant prism knobs that withstand high temperatures during the reflow process.]

Material and finish selection also impacts hardware strength. If not plated properly, the metal used in the screw design can retain absorbed hydrogen (hydrogen embrittlement), which can affect a screw’s ability to withstand applied forces. A qualified supplier will perform such tests as hydrogen embrittlement after the plating process, which can prevent issues when forces are applied in the field.

The installation process can also contribute to added service costs. During PC board assembly, stress created by pressing captive hardware through pre-drilled holes can cause cracking or damage the layers of the PC board, resulting in added scrap costs. Different installation processes are now available, such as surface mount technology (SMT), which allows captive screws to be attached to the PC board during the reflow soldering process at the same time as other surface mounted components, resulting in lower overall installation cost.

Choosing a proven supplier

Open source models offer unlimited options for new lower cost suppliers, but choosing inject/eject mechanisms and captive hardware from a proven supplier can save time and additional engineering resources from the start of the project. Proven engineering expertise can help address potential risks early in the design and development, preventing the risk of downtime and added service costs.

Integrating a validated solution at the beginning of the design through a proven supplier that offers DFM or DFEA is more beneficial over time because it reduces the likelihood of component failure in the future. As a result, engineers can spend more time dedicated to their equipment and launching the project on time.

When choosing enterprise hardware products, engineers should also examine a supplier’s manufacturing processes, including die casting capabilities and in-house powder coating, as well as how the supplier manages their supply chain. Additionally, enterprise hardware products must be compliant with global industry standards, such as RoHS or other directives, regardless of where they are manufactured.

Choosing a supplier with a global footprint allows manufacturers to secure resources wherever they are building equipment in the world. An application can be designed in one country and manufactured in another, and replacement components can be sourced where they are needed.

Conclusion

Latches and fastening products engineered at a lower cost may not always meet the same level of quality as solutions acquired from a proven supplier. The same investments made to protect valuable data stored in the data center from virtual threats should also be applied at the physical level, which includes the racks and switches that house and transmit the data. By specifying enterprise hardware engineered with quality materials, engineers can prevent service issues and downtime, while keeping data safe and secure.

Robert Shelley is Business Development Manager for Southco’s Enterprise Hardware business. He has over 20 years of experience working in enterprise hardware solutions, holds a Bachelors of Science in Business Administration and Management from Kutztown University of Pennsylvania, and holds an Associates in Mechanical Engineering from the Pennsylvania Institute of Technology.

Southco
www.southco.com
www.linkedin.com/company/southco-inc-
www.twitter.com/southco
www.facebook.com/southco

Robert Shelley, Southco
Previous Article
Specifying switches for hazardous environments
Specifying switches for hazardous environments

In specifying switches as part of a wider device or system, design engineers have much to consider. Such ch...

Next Article
Improving smartphone cameras with color sensor technology
Improving smartphone cameras with color sensor technology

The world of digital image capture has evolved dramatically in the past decade. Perhaps most striking and r...